Boat Outfitting - Radar/TV Mounts

Scanstrut Dual PowerTower Strut - Open Array [DPT-OA]

Dual PowerTower® Strut - Open Array

The Modular Dual PowerTower® has been designed to allow your open array, radar, Satcom and camera to be mounted together in one single space-saving modular installation. 

Specifications:

• Material: 6082 Aluminum extrusion
• Coating: Polyester powder
• Finish: Gloss white
• Mounting plate(s) sold separately 

Specifications:

• Type: Dual Mount
• Construction: Powder Coated Aluminum
• Box Dimensions: 13"H x 24"W x 43"L WT: 21.15 lbs
• UPC: 5060114796324

Scanstrut Modular Dual PowerTower Strut - Compact Domes Only [DPT-R-COMP]

Modular Dual PowerTower Strut - Compact Domes Only

The Modular Dual PowerTower has been designed to allow your open array, radar, Satcom & camera to be mounted together in one single space-saving modular installation.

Features:

• Dual Power Tower strut (Radome) (compact)
• Material: 6082 Aluminum Extrusion
• Coating: Polyester Powder
• Finish: Gloss White
• Application: Marine

Specifications:

• Construction: Powder Coated Aluminum
• Type: Aft Leaning Mount
• Box Dimensions: 10"H x 14"W x 27"L WT: 9.2 lbs
• UPC: 5060114796331

StarPod Mini System with StarTower for Starlink Mini Dish (11.75 x 10.2″ Dish Size) *Starlink Dish Not Included

StarPod Systems are designed to provide a strong, sturdy, and attractive mounting solution for Starlink on board boats with a hardtop, radar arch, or other flat mounting surface. The waterproof housing incorporates an internal swivel tube, which allows the dish to be rotated to optimize the view of Starlink satellites if necessary. The 10-degree housing angle facilitates rainwater runoff to prevent signal degradation that can occur when water accumulates on a flat-mounted Starlink dish. The StarTower base is solidly built with 8 mm-thick aluminum and powder-coated with a high-gloss white finish. The bottom base of the StarTower measures 7″ square.

Be sure to choose the right StarPod System to match your Starlink dish model:

• For the Starlink Mini Dish (11.75 x 10.2″ dish size):
• SP100 Housing Only for DIY mounting (7″ diameter circular mounting surface)
• SPS1000 for mounting a Starlink Mini Dish on a Flat Surface *You’re already on this product page!*
• SPS1001 for mounting a Starlink Mini Dish on a Horizontal Rail
• SPS1002 for mounting a Starlink Mini Dish on a Vertical Rail
• SPS1003 for mounting a Starlink Mini Dish on a Thule WingBar Evo Roof Rack (COMING SOON)
• SPS2000 for Starlink Gen2 Actuated Dish (20.2 x 11.9″ dish size)
• SPS3000 for Starlink Gen3 Standard Dish (23.4 x 15.07″ dish size)

What are the benefits of mounting a Starlink dish in a StarPod?

StarPod protects Starlink and completely encloses the Starlink antenna in a very sturdy and attractive waterproof housing. Our testing has proven that there is no degradation of signal while inside the thermoformed acrylic-capped ABS housing.

Mounting a Starlink dish inside a StarPod provides additional protection from water intrusion, just as all NavPods have done for other Marine Electronics for over 25 years.

How do I mount a Starlink dish inside a StarPod?

The kickstand base that comes with a Starlink Mini dish is not utilized when mounting inside a StarPod; only the dish itself is used. We recommend completing the initial Starlink setup process before mounting the dish inside a StarPod (refer to your Starlink setup/installation guide for this process). Once the initial Starlink setup process is complete, the dish can be mounted inside the StarPod housing (using the instructions and hardware included with the StarPod).

All NavPods Feature:

• Structural Rigidity – The Gen3 enhancements now include a thicker gauge acrylic-capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and the more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.
• Waterproof Seal – All NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection for your Marine Electronics. StarPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to “compression set” like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics. The gasket will continue to do its job.
• Stainless Steel Hardware – We use all 316 stainless steel hardware that is supplied with each NavPod.
• Commitment to Quality – We stand behind our commitment by offering a 10-year warranty on all new NavPods, including the StarPod.

Complete Spreader Kit for Radars & Satdomes for Mounts Ending in M1

This three-piece kit consists of a mid-section and two spreaders. Four bolts are used to secure each spreader to the midsection. The spreaders are tapered and angled aft so that whatever you decide to put on there will not interfere with the radar or satdome that you have on your mount. All the wiring from your GPS unit or antenna can be routed internally through the spreaders and into the mount itself. Not only does this help with security but it also makes for a very nice and clean installation. All the parts that make up the spreader kit are bolted together with rubber gaskets in between each part to prevent any water intrusion. Each spreader kit now comes with two S.S. 1-14 threaded adapters (SP7SS).

Complete Spreader Kit for Radars & Satdomes for Mounts Ending in M2

This three-piece kit consists of a mid-section and two spreaders. Four bolts are used to secure each spreader to the midsection. The spreaders are tapered and angled aft so that whatever you decide to put on there will not interfere with the radar or satdome that you have on your mount. All the wiring from your GPS unit or antenna can be routed internally through the spreaders and into the mount itself. Not only does this help with security but it also makes for a very nice and clean installation. All the parts that make up the spreader kit are bolted together with rubber gaskets in between each part to prevent any water intrusion. Each spreader kit now comes with two S.S. 1-14 threaded adapters (SP7SS).

NavPod StarPod 2 System f/Starlink Gen2 Actuated Dish (20.2 x 11.9 Dish Size) [SPS2000]

StarPod 2 System for Starlink Gen2 Actuated Dish (20.2 x 11.9″ Dish Size)

*Starlink Dish NOT INCLUDED

The StarPod 2 System is a waterproof, secure, attractive mounting solution for your Starlink Gen2 Actuated antenna. The housing features a built-in 10-degree angle and full swivel adjustability so that the dish can be manually adjusted for an optimized view of Starlink satellites in the sky. The 10-degree angle also prevents water from pooling on top of the housing, which can cause signal interference.

Note: Assembly of this product requires the use of a deck fill wrench (Groco model SW-2531 or equivalent product). This tool is NOT included with the StarPod.

What are the benefits of mounting a Starlink dish in a StarPod?

StarPod protects Starlink and completely encloses the Starlink antenna in a very sturdy and attractive waterproof housing. Our testing has proven that there is no degradation of the signal while inside the thermoformed acrylic-capped ABS housing.

Mounting a Starlink dish inside a StarPod provides additional protection from water intrusion, just as all NavPods have done for other Marine Electronics for over 25 years.

Features:

• Structural Rigidity – The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening, and the more uniform the pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.
• Waterproof Seal – All NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection for your Marine Electronics. StarPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with an improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to a “compression set” like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics. The gasket will continue to do its job.
• Nickel Chrome-Plated Stainless Steel – We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for matching to the NavPod wrench for better holding ability when tightening. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!
• Commitment to Quality – We stand behind our commitment by offering a 10-year warranty on all new NavPods, including the StarPod.

This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Scanstrut SC80 Satcom Mount - Stainless Steel [SC80]

Ships Direct From Manufacturer 

SC80 Satcom Mount - Stainless Steel

Manufactured from marine grade Stainless Steel.

Your chosen antenna will attach through external fixings and pre-drilled mounting holes, making installation and maintenance easy to perform.

Compatible Units:

• JRC - JUE-501 Fleetbroadband
  • KVH - Fleet BB 500 / V7, V7IP(M9 matching dome), TracPhone V7-HTS, TracVision G8, M9, TV8

Features:

• Reduces the overall footprint of the Satcom antenna 
• Mirror polished for a hi-end finish
• Satcom mounting hardware is hidden internally
• Watertight installation 

Technical Specifications:

• Material - Stainless Steel
• Height - 3.14" (80mm)
• Mounting Type - Vertical

In the Box:

• Mount
• Mount seal
• Mounting hardware (excluding screws/bolts) 
• Instruction manual 

*Sold as an Individual

Specifications:

• Construction: Stainless Steel
• Height: 3.14
• Type: Vertical Mount
• Box Dimensions: 6"H x 17"W x 22"L WT: 18.35 lbs
• UPC: 5060114790896

Quick Guide (pdf)

Scanstrut Tapered Radar Mast f/Radomes, Lights, Cameras, GPS/VHF Antennas [PTM-R1-2]

Ships Direct From Manufacturer 

Tapered Radar Mast

For Radomes, Lights, Camera and GPS/VHF Antenna

Single combintation mount for radar, lights, GPS/VHF antennas, cameras or search lights, with each item perfectly positioned for maximum performance.

Features: 

• Undrilled top plate to fit any light
• Install up to 4 GPS/VHF antenna
• Hollow wings and stem allow hidden cabling
• Compatible with all current 18" and 24" radomes
• Small base footprint (same as Dual PowerTower)
• Removable 'wings' for safe low cost shipping

Specifications:

• Type: Dual Mount
• Box Dimensions: 13"H x 31"W x 37"L WT: 22 lbs
• UPC: 5060114793392

Quick Guide (pdf)