Automotive/RV

Power-Pac 14AH Power Supply  

The 12V DC power supply features built-in backup batteries, which are charged during normal operation and then continue to power radios and critical navigation equipment when AC power is lost. The Power-Pac is ideal for commercial vessels, work boats, and yachts.

The Power-Pac’s highly regulated, low-rising 10-amp output powers radios and other sensitive communications equipment without causing RF or audio interference. At the same time, it floats and charges one or two (depending on the model) built-in 7-amp/hour backup batteries. These are kept at peak charge during the normal functioning of the unit when AC is being supplied. In the event of a loss of AC power, the internal batteries automatically take over to power communication equipment, providing a true uninterruptible DC source.

Features:

• Highly regulated, low ripple, noise-free 12-volt output
• Built-in, “on-line” stand-by battery provides immediate backup power in case of AC power loss
• Internal mounting space and terminals for conversion of the 7 A/H model into the 14 A/H model
• Output “Normal” indicator L.E.D.
• “Back-up power only” warning light
• Audible and visual low battery (10.7 VDC) voltage indicators
• Low battery warning buzzer mute switch
• Automatic low battery (10.3 VDC) voltage disconnect
• Low voltage disconnect override button
• Over-voltage protection
• Current limit protection
• Input/output fused
• Separate output terminals are provided for charging external batteries
• 115/230 50-60 Hz input, selected by a slide switch on the rear panel

Specifications:

• Battery Capacity: 14 amp/hour  
• Case Size (H x W x D): 5.3 x 9.0 x 10.5 inches (13.3 x 22.9 x 26.7 centimeters)  
• Weight: 24 lbs. (10.9 kg)
• Input: 115/230 VAC, 50-60 Hz.
• Output: 13.6 VDC @ 5A cont., 10A Int.
• Regulation: 1% line and load
• Ripple: 1% P-P
• Operating Temp: 0-40 degrees C

With a 14 Amp/Hour Battery Installed, the Unit Provides Approximately the Following Power:

• 7 amps for 100 min.
• 10 amps for 60 min.
• 15 amps for 30 min.
• 20 amps for 15 min

*Assuming battery at full charge when a.c. power failed.

The Power-Pac 7 A/H (single battery model) can power a 25-watt transceiver for up to 3 hours, based on a 20% transmit/receive duty cycle. Power-Pac 14 A/H can provide the same service for up to 6 hours. Provision is made for expanding backup power up to twelve hours (in this example, longer under lesser loads) with the installation of additional externally wired batteries (total 28 amps/hours max.). Batteries are automatically recharged when the AC is restored.

The operator is kept informed of all important functions, such as AC input, DC output, and battery status, with front panel indicator lights and a low battery warning buzzer.

Protection:

• AC Input fuse
• Internal and external Battery fuses
• Over Voltage
• Current Limit
• Automatic Thermal Shutdown
• Low Battery Disconnect

Mechanical Details:

• Vinyl Laminated aluminum case
• 6’ standard AC power cord
• Ac input selector switch

Battery Details:

• Sealed Lead Acid, Deep-cycle.
• Certified by DOT and IATA for shipment by Air
• Weight per 7 AH Battery: 6 lbs.
• Size (inch): 6” x 3.75” x 2.5”

Options:

• Form C AC Failure Contacts (Contact factory for details)
• Extra batteries, sold separately 7 A/H increments; each Power Pac will accommodate 28 A/H max. (14 internal, 14 external)

Xantrex TRUEcharge3 60A 3 Bank Battery Charger - 12V [804-1260-10]

TRUEcharge™3 60A 3 Bank Battery Charger - 12V

TRUEcharge3 battery chargers lead the industry with a small footprint and ultra-compact design. In addition to meeting global safety and regulatory standards, they feature low electrical interference and efficient power factor-corrected multistage charging. The TRUEcharge3 Chargers can be mounted in multiple positions thanks to their inherent drip-proof design characteristics. Unlike its predecessors, TRUEcharge3 is lithium-ion battery compatible.

Designed for recreational and commercial applications worldwide, TRUEcharge3 accepts 90–265 Vac, and 47–63 Hz, which makes traveling abroad and handling poor-quality power a breeze. The easy-to-read display of the TRUEcharge3 12 V models can be enhanced with an optional remote panel. Each model has built-in protection against surges and spikes on the AC power line.

Features:

• Microprocessor-controlled, multistage charging algorithms
• Settings for two and three-stage charging
• Battery-equalization feature
• Settings for flooded, gel, AGM, or lithium-ion batteries
• Equipped with parallel stacking (remote panel required)
• Ability to charge batteries drained to extremely low voltage
• Added quiet mode

Protection Features:

• Reverse-battery polarity protection
• Drip-proof design
• DC over-voltage protection
• Over-temperature protection
• Circuit breaker protection

Three-Stage Charging

Multistage charging ensures batteries receive optimum charging, but with minimal wear and tear, regulating the voltage and current delivered to the batteries in three automatic stages:

• Bulk: Replaces 70–80% of the battery’s state-of-charge at the fastest possible rate
• Absorption: Replenishes the remaining 20–30% of charge, bringing the battery to a full charge at a slow, safe rate
• Float: Voltage is reduced and held constant to prevent damage and maintain batteries at a full charge for the remaining 20–30% of charge, bringing the battery to a full charge at a slow, safe rate

Power Factor Corrected (PFC) Charging

Less shore power is required for charging batteries, freeing up more usable AC power for running electrical devices and appliances and reducing the likelihood of tripping shore power breakers.

Electrical Specifications (@ 25 degrees C unless otherwise noted):

• Output Current (nominal): 60 A 
• Output Voltage (nominal, depending on settings): Charge 14.2–15.5; Float 13.4–13.8 Vdc; 16 V
• DC Output Connections: Three
• AC Input Voltage: 90–265 Vac; 47–63 Hz 120 Vac, 230 Vac, 240 Vac nominal
• Temperature Compensation: Three settings 
• Charger Efficiency: > 80%
• Battery Type: Gel, Flooded, AGM, LiFePO4 
• Minimum Recommended Battery Bank Size: 120 Ah 

General Specifications:

• Operating Temperature Range: 0–60°C (32–140°F) 
• Storage Temperature -40–80°C (-40–176°F)
• Battery Connection: Three positive terminals and one negative terminal
• Dimensions (H x W x L): 90 x 170 x 340 mm (3.5 x 6.7 x 13.4”)
• Weight 4.5 kg (9.9 lb)

Regulatory Approvals 

Meets CSA 60335-2-29, CE Marked for the Low Voltage Directive (safety) and the EMC Directive, UL1564, IEC 60335-2-29, IP32 per EN.IEC 60529, FCC Part 158, Canada ICES-003 Class B emissions limits, ABYC A-31, and DOE/CEC energy efficiency compliant.

This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Specifications:

• Charger Output - Amps: 60a
• Charger Output Voltage: 12v
• Charging Banks: 3
• Portable: No
• Box Dimensions: 6"H x 11"W x 17"L WT: 8.95 lbs
• UPC: 715535920852

Quick Guide (pdf)
Owner's Manual (pdf)
Brochure (pdf)

RIGID Industries E-Series Pro 10" Spot - Black [110213]

E-Series Pro 10" Spot - Black

The E-Series is one of RIGID's most versatile, all-around lighting solutions and recent enhancements in LED technology deliver up to 111 percent more raw lumens than ever before with the E-Series PRO. Among RIGID's most popular product lines, the E-Series PRO has recently benefited from several upgrades to improve both looks and performance. Plus, prominent RIGID branding and blacked-out circuit boards give the E-Series PRO a refined look. Available with your choice of optics, the E-Series features a host of beam options, including Spot, Flood, Driving, Hyperspot, Diffused, Driving/Spot combo, Spot/Flood combo, Spot/Hyperspot combo, and Midnight Edition. These and other innovations make it one of the brightest and most efficient LED light bars on the market. The E-Series was born off-road, but its versatility makes it well suited for use with power sports, marine, general automotive, and even first responder applications. Own The Night with RIGID's E-Series double-row LED light bar.

Features:

• 50,000 Plus Hour Lifespan
• 9-36 V DC
• Durable UV Resistant Powder Coat
• High-Grade Aluminum Alloy
• Integrated Thermal Management System
• Impact Resistant Polycorbonate Lens
• Over/Under Voltage Protection
• RFI/EMI Protection
• Reverse Polarity Protection
• RoHS Compliant
• IP68 Compliant - Dust/Water Ingress
• Patented Optics
• SAE J575 Compliant - Shock/Vibration
• Available In White And Black Housing
• Pressure Equalizing Vent
• Waterproof Connector (Exclusions Apply)
• Limited Lifetime Warranty
• Off-Road Use Only

Specifications:

• Size: 10"
• Weight (lbs): 5.00
• Optics: Spot
• Watts: 168
• Amp Draw: 12
• Voltage Max: 36
• Raw Lumens: 1584
• Lux @ 10m: 3368
• Beam Distance @1Lux: 580
• Beam Distance @.25Lux: 1160
• Horizontal Beam Angle: 17.3

What's Included?

• 2 Black Powder Coated, L-shape brackets
• Deutsch Connector (4”-10”)
• Open Leads, No Connector (20”-50”)
• Harness with Switch

Specifications:

• Beam Pattern: Spot
• Housing: Black
• Length (Inches): 10"
• Voltage - Input Range (Volts): 12v
• Box Dimensions: 7"H x 7"W x 13"L WT: 6.55 lbs
• UPC: 849774028939

Xantrex TRUEcharge3 20A 3 Bank Battery Charger - 24V [804-2420-10]

TRUEcharge™3 20A 3 Bank Battery Charger - 24V

TRUEcharge3 battery chargers lead the industry with a small footprint and ultra-compact design. In addition to meeting global safety and regulatory standards, they feature low electrical interference and efficient power factor-corrected multistage charging. The TRUEcharge3 Chargers can be mounted in multiple positions thanks to their inherent drip-proof design characteristics. Unlike its predecessors, TRUEcharge3 is lithium-ion battery compatible.

Designed for recreational and commercial applications worldwide, TRUEcharge3 accepts 90–265 Vac, and 47–63 Hz, which makes traveling abroad and handling poor-quality power a breeze. The easy-to-read display of the TRUEcharge3 24 V models can be enhanced with an optional remote panel. Each model has built-in protection against surges and spikes on the AC power line.

Features:

• Microprocessor-controlled, multistage charging algorithms
• Settings for two and three-stage charging
• Battery-equalization feature
• Settings for flooded, gel, AGM, or lithium-ion batteries
• Equipped with parallel stacking (remote panel required)
• Ability to charge batteries drained to extremely low voltage
• Added quiet mode

Protection Features:

• Reverse-battery polarity protection
• Drip-proof design
• DC over-voltage protection
• Over-temperature protection
• Circuit breaker protection

Three-Stage Charging

Multistage charging ensures batteries receive optimum charging, but with minimal wear and tear, regulating the voltage and current delivered to the batteries in three automatic stages:

• Bulk: Replaces 70–80% of the battery’s state-of-charge at the fastest possible rate
• Absorption: Replenishes the remaining 20–30% of charge, bringing the battery to a full charge at a slow, safe rate
• Float: Voltage is reduced and held constant to prevent damage and maintain batteries at a full charge for the remaining 20–30% of charge, bringing the battery to a full charge at a slow, safe rate

Power Factor Corrected (PFC) Charging

Less shore power is required for charging batteries, freeing up more usable AC power for running electrical devices and appliances and reducing the likelihood of tripping shore power breakers.

Electrical Specifications (@ 25 degrees C unless otherwise noted):

• Output Current (nominal): 20 A 
• Output Voltage (nominal, depending on settings): Charge 28.4–31.0 Vdc; Float 26.8–27.6 Vdc; 32 Vdc
• DC Output Connections: Three
• AC Input Voltage: 90–265 Vac; 47–63 Hz 120 Vac, 230 Vac, 240 Vac nominal
• Temperature Compensation: Three settings 
• Charger Efficiency: > 80%
• Battery Type: Gel, Flooded, AGM, LiFePO4 
• Minimum Recommended Battery Bank Size: 40 Ah 

General Specifications:

• Operating Temperature Range: 0–60°C (32–140°F) 
• Storage Temperature -40–80°C (-40–176°F)
• Battery Connection: Three positive terminals and one negative terminal
• Dimensions (H x W x L): 70 x 170 x 250 mm (2.8 x 6.7 x 9.8”)
• Weight 2.2 kg (4.8 lb)

Regulatory Approvals 

Meets CSA 60335-2-29, UL1564, IEC 60335-2-29, IP32 per EN.IEC 60529, FCC Part 158, Canada ICES-003 Class B emissions limits, ABYC A-31, and DOE/CEC energy efficiency compliant.

This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Specifications:

• Charger Output - Amps: 20a
• Charger Output Voltage: 24v
• Charging Banks: 3
• Portable: No
• Box Dimensions: 6"H x 11"W x 13"L WT: 6.15 lbs
• UPC: 715535920937

Quick Guide (pdf)
Owner's Manual (pdf)
Brochure (pdf)

115-12-20A Power Supply

This super-rugged DC power supply is ideal for powering 12-volt communication and navigation equipment onboard commercial vessels where reliability is essential. The proven linear circuit design provides pure noise-free output and a long service life.

Features:

• Excellent Regulation and Ripple Spec (output voltage maintained within 1% under all rated line and load conditions)
• Polyurethane conformal coated PC board and corrosion-resistant heavy-duty aluminum case with integral shock mounts assure survival in hostile environments
• The heat generated by semi-conductors is extracted and dissipated by large heat sink fins for cool operation
• Protection: overvoltage, current limit; (set @ 105% of intermittent rating), thermal overload, and input/output fusing
• Thermally activated cooling fan on “CD” units

Specifications:

• Nominal Input/VAC: 115/230    
• Maximum Input Current @115: 5.5
• Maximum Input Current @230: 2.5
• Output Amperage (Intermittent): 20
• Output Amperage (Continuous): 8
• Weight: 20 lbs. / 9.1 kg

Case Size:

• H x W x D (inch): 5.7” x 4.8” x 16.3”

Input Range

105-125/210-250 VAC (selectable), 50-60 Hz; Derate to 50% output below 110 and 220 VAC

Operating Temperature

Standard Units - 0-50 degrees C, Derate linearly from 100% @ 40 degrees C to 50% @ 50 degrees C thermal shutdown @ 85 degrees C case temperature

Duty Cycle:

• Intermittent: 20 minutes max on time, 20% duty
• Continuous: 24 hours/day 100% Duty

Options:

• Modify for use as a battery charger
• The output voltage is adjusted (see Output Voltage for range)
• Transfer relay for back-up battery in event of power failure (ERC option)

Output Voltage:

• 13.6 VDC (internally adjustable 12.6-14.5 VDC)
• Ripple: 40mV P-P (@ 110-125 / 220-250 VAC input)
• 1% Line and Load (@ 110-125 / 220-250 VAC input)

Mechanical:

• Powder-coated aluminum heat sink case
• Front panel terminal block
• Heavy-duty mounting flange
• Conformal-coated PC board

60" Double Row LED Bar - Pro Series 2.0 - 5W Combo White

The 60" Marine Curved was designed for serious fishermen who spend their nights on the water. Whether heading out early or returning late, this light bar will get you home safely. With a whopping 82,500 raw lumens, you're bound to light up everything in your path. If you know salt water, you know complete destruction of equipment from salt water corrosion. The Military grade breather and powder-coated water-proof design keep the LED Marine light bar series sealed with no risk of moisture leaking through.

Features:

• A combination flood/spotlight pattern offers a superior lighting pattern
• Throw light over 2500m
• T-Top light for large center consoles, sportfish, yachts
• Off-road LED light bar
• Work light for construction sites
• Bari-coat ceramic coating for protection from UV, saltwater, and corrosion
• Hydrex 2 Stage gasket redundant waterproofing seal
• Dynamax housing to withstand the harshest beating possible
• Updated reflectors to produce a more efficient throw
• Pro Series brackets are 9GA thick 316 stainless

Technical Specifications:

• Total Wattage: 600w
• Amp Draw: 21
• Led Quantity: 120
• Weight: 19.8lbs
• Raw Lumens: 82,500
• Warranty: Lifetime
• IP Rating: IP69K
• Voltage: 9-36V DC

In the Box:

• Light bar
• 10 AWG wire Lead
• Mounting brackets

 *Sold as an Individual

Specifications:

• Beam Pattern: Spot-Flood Combo
• Housing: White
• Length (Inches): 60"
• Voltage - Input Range (Volts): 12/24v
• Box Dimensions: 6"H x 9"W x 65"L WT: 15 lbs
• UPC: 850044517534

RIGID Industries Radiance+ SR-Series LED Light - 8 Option RGBW Backlight - 30" [230603]

Radiance+ SR-Series LED Light - 8 Option RGBW Backlight - 30" 

The versatility of the RIGID Radiance lighting family just got even better with the introduction of the Radiance Plus SR-Series. RIGID’s RGB LEDs provide the user with the ability to toggle between eight available backlight options with the flip of a switch: Red, Green, Blue, Light Blue, Purple, Amber, White or Rotating. The RIGID Radiance Plus SR-Series single-row LED light bar is the perfect solution for those who want RIGID’s legendary quality at a level everyone can attain. Utilizing RIGID’s LED technology, the Radiance Plus light bars feature the same superior build quality as the rest of RIGID’s lighting products, providing reliable and efficient lighting on demand. The Radiance Plus SR-Series LED light bars are built with the same sleek low-profile high-grade aluminum alloy housing as the legendary SR-Series, but that’s where the visual similarities end. Inside, the Radiance SR-Series is feature-packed, with a black exposed circuit board, optimized forward projecting Broad Spot optics, prominent RIGID branding plates, and RGB LEDs with seven backlight colors. Available in 10, 20, 30, 40, and 50-inch lengths, and fits all existing SR-Series mounting options. The wiring harness and switch are sold separately (#40200). The RIGID Radiance Plus SR-Series light bar is for the customer who wants a truly custom look, making it easier than ever to Own The Night. 

Features:

• Same Construction As RIGIDs SR-Series
• Fits All SR-Series Light Covers And Mounts
• Black Exposed Printed Circuit Board
• 8 Back Lighting Options: Red, Green, Blue, Light Blue, Purple, Amber, White, or Rotating
• 10 Year Warranty
• 9-15 V DC
• Harness And Switch Sold Separately, Part Number 40200
• Back Lighting Independently Controlled Using Switch Logic
• Black Powder Coat Finish
• Pressure Equalizing Vent
• IP68 Compliant - Dust/Water Ingress
• High-Grade Aluminum Alloy Housing And Heat Sink
• Over/Under Voltage Protection
• High Impact Polycarbonate Lens
• Mounting Brackets Included
• RFI/EMI Protection
• RoHS Compliant
• Off-Road Use Only

Specifications:

• Optics: Broad Spot
• Watts: 137
• Amp Draw: 10.5
• Raw Lumens: 16320
• Lux @ 10m: 1976.42
• Beam Distance @ 1Lux: 444.55
• Beam Distance @ .25Lux: 889.15
• Horizontal Beam Angle: 23.7

Product Comes With:

• Light Bar
• Mounting Hardware

Specifications:

• Length (Inches): 30"
• Box Dimensions: 7"H x 7"W x 34"L WT: 8.3 lbs
• UPC: 815711014853

Pro Series 3.0 Curved Double Row 50" LED Light Bar - Combo Optics - White Housing

With this Black Oak 50-inch marine LED light bar, users may never have to search for a Buoy again. This 50" light bar is Black Oak's largest, most intense, and frankly, most bad-ass light we have ever manufactured! Whether users want to light in between those dark river channels or locate the shoreline, this dual-row beauty will act as a secondary lighthouse! Illuminating the water using Osram's high-quality 5-watt LED options, it's easy to see how this cutting-edge LED marine light bar packs such a punch. 

With saltwater comes complete destruction of equipment from saltwater corrosion. Black Oak's military-grade breather and powder-coated water-proof design keep the LED Marine light bar series sealed with no risk of moisture leaking through.

Black Oak has taken the LED game to the next level. The Pro Series 3.0 features top-of-the-line LED tech, boasting a 20% increase in lumens, making this series of lights one of the brightest on the market.

Features:

• 360° Ceramic Protection against UV, Salt Water & Corrosion
• 2 Stage Hydrex Seal Lock for IP69 protection and a fully submersible light bar
• Heavy-duty Dynamax housing for a 4x stronger frame
• Premium Dupont powder-coating for the highest quality and most resistant finish
• Combination Flood/Spot light pattern offers a superior lighting pattern
• Multi-mount brackets made of 9 gauge marine grade Stainless Steel
• Lens cover made of Lexan with a UV protectant

Activities & Uses: 

• Perfect above the windshield on Jeeps and Trucks
• Throw light over 2000m!
• T-Top light for 30ft+ vessels
• Off-road LED light bar
• Work light for construction sites

Technical Specifications:

• Total Wattage: 500W
• Amp. Draw: 21
• LED Quantity: 100
• Weight: 18.0 lbs.
• Raw Lumens: 66,000
• Warranty: Lifetime
• IP Rating: IP69K    
• Connection: Deutsch connector
• Dimensions with Mounting Bracket (Width x Height): 51.4" x 4.125"

In the Box:

• Light bar
• Complete wiring harness with fuse, relay, and switch
• 12 gauge wire
• Mounting brackets
• All hardware is ready to install! 

*Sold as an Individual

Specifications:

• Beam Pattern: Spot-Flood Combo
• Housing: White
• Length (Inches): 50"
• Voltage - Input Range (Volts): 12v
• Box Dimensions: 6"H x 7"W x 55"L WT: 17.25 lbs
• UPC: 850044517572